The automobile Stereo Installation Guide

The Car Stereo Installation Guide

If you find the dog pros charge a great deal of money to setup the auto stereo, it can be done yourself and save that quantity paid towards expert.

car video



It's not at all very difficult to put in a car audio and video system; it is only that it seems so. You simply require a little bit of precision and focus that will put inside the system. No specialized skills or intimate knowledge on mobile entertainment is required for this reason. You can actually position the excess money that you save in the installation process behind the best car audio and video system itself, this provides the particular scope to acquire something better.

While initiating the procedure, you'll need to be careful as loss of concentration can result in damages of equipments of one's car and spoil the caliber of the automobile stereo audio. You should be systematic because plugs enter their respective sockets only.

How to get started

- When you buy a new car audio and video system, determine if it can be fitting properly for the location of the existing speakers. Along with your new car stereo system, also buy a cabling strap which can be mechanized in accordance with the car and stereo model and works brilliantly for brand spanking new car stereo systems.

- Prior to getting down to your work, request few tools like electrical tape, wire strippers, screwdrivers and wire cutters.

- If you aren't capable to unscrew out your old audio system, require some help with the way to take it out of your dashboard where the new car stereo will fit into.

Removing the old car stereo

- Initially, detach the negative cable through the battery as you must not help that cable connected.

- Get the dash board of your car to take out the old car audio system and appearance the wires which might be linked in the dust. Either there would be considered a single plug with too many wires attached with them in any other case a cluster of single wires. In case there is the later one, it is advisable to disconnect them one-by-one in order to avoid confusion.

- Place the connectors in to the new cabling strap and plug it into a new car stereo.

For those who have successfully done this, you can abandon on the next section.

Connecting the Wiring Manually

- When there is no cabling strap support, attach all the wires at the back of the rear of the new car stereo cautiously.

- Slowly detect the positive wires from each speaker and connect them at the back of the positive connector of the new car stereo. Similarly, perform the same goes with the negative wires of each speaker and connect them to the negative connectors of the mobile entertainment system. In case, when there is only 1 wire coming out from the speakers, the speakers are grounded on the chassis and you also will have to put in a new wiring for that speakers.

- The negative wire, along with metal and never plastic should be connected with a screw near the radio from the dash.

- The ignition wires and the 12 constant, both positive is supposed to be connected together to the back of the new stereo.

Setting up the car stereo

- All of the wires needs to be attached with just one connector that is popping out in the additional cabling strap or even the the one that came along with all the car stereo audio where all of the wires are already attached to.

- If you find no new bracket to set the newest car stereo, use the old the one that previously held the factory stereo system.

- Now position the final connector which is cabling strap behind the stereo system with the antenna, an extended wire that was previously connected at the back of the old stereo and the power wire in the back of the new car stereo unit.

- Squeeze stereo audio inside dashboard in which the previous system was placed along with put back the screws since you may require testing the device.

- This is the time when you should again attach back the negative cable to the battery.

- Start your automobile and also power on the car stereo unit. Check keenly, whether all of the speakers attached is working fine.

- Put the screws back into the stereo system and set the cover of the dash board back on.

In case outcomes are unsatisfactory

If you still obtain the product is not delivering satisfying results, use a wooden or fiberglass flummox that the audio quality can get better and you can even include noise reduction objects like liners, glue strips, invest more carpets about the inner panel and rehearse sprays.

car video